Skip to main content
Version: 0.1.0

Operating a SAG deployment

Runbooks for the things an operator has to do occasionally and must not get wrong. Each one states what breaks if it is done in the wrong order.

Rotating the master secret​

SAG_SECRET protects sessions, in-flight transactions, authorisation codes and access tokens. Rotating it is routine and does not have to sign anybody out.

The rule: the current secret seals, every configured secret opens. So a rotation is done in two deployments, not one.

  1. Deploy with both. Set SAG_SECRET to the new value and SAG_SECRET_PREVIOUS to the old one.

    SAG_SECRET=<new>
    SAG_SECRET_PREVIOUS=<old>

    From this moment everything new is sealed under the new secret, and anything sealed under the old one still opens. Nobody is signed out, and anybody halfway through typing a code can still finish.

  2. Wait. Long enough for every existing session to have been used at least once, because using a session rewrites its cookie under the new secret. One SESSION_TTL is the safe answer - by then every session has either been re-sealed or expired on its own.

  3. Deploy without the old one. Remove SAG_SECRET_PREVIOUS. Any session that was never used during the window is now invalid, and those people sign in again.

Doing step 3 immediately signs everybody out. That is a legitimate thing to want after a suspected compromise - it is the revocation mechanism - but it is not a rotation.

Generate a new secret with:

npm run keygen -- --secret-only

Rotating the signing key​

Different from the master secret, and slower, because relying parties cache the JWKS.

  1. Publish both. Add the new key as an additional algorithm, or configure a second key of the same algorithm. Both appear in /jwks.json, and the old one stays primary. Relying parties pick keys by kid, so nothing breaks.
  2. Wait for the JWKS cache to turn over. SAG serves it with a five minute cache, but a relying party's own library may cache for much longer. An hour is comfortable; a day is safe.
  3. Make the new key primary. New id_tokens are signed with it. Anything already issued still verifies, because the old key is still published.
  4. Retire the old key once nothing signed by it can still be within its lifetime - ID_TOKEN_TTL plus a margin.

Never do steps 1 and 3 in one deployment: a relying party with a cached JWKS that does not yet contain the new key will reject every token until it refetches.

Warning with SUBJECT_SALT​

Changing it gives every person a new sub at every relying party, which orphans their accounts - the relying party sees a brand new user and the old records become unreachable. There is no migration path short of every relying party re-linking accounts by email.

If it has to change, treat it as a migration project, not an operational task. SAG_ISSUER is deliberately not part of the derivation, so renaming a deployment is not this - see ADR 0011. Turning SANITISE_PLUS_EMAILS on or off after people have signed in is: it merges or splits every account whose owner uses a plus tag.

Suspected compromise​

  • Master secret leaked. Deploy a new SAG_SECRET with no SAG_SECRET_PREVIOUS. Every session, transaction and code is invalidated at once. Everybody signs in again.
  • Signing key leaked. Configure the new key and make it primary in one deployment, and remove the old key at the same time. This will break relying parties with a stale JWKS for as long as their cache lasts, which is the correct trade: a leaked signing key means anybody can mint an id_token for anybody.
  • A client secret leaked. Change that client's secret. Nothing else is affected, because a code is bound to its client.

Reading /alive​

Nothing to read: a 200 with the body ok means a process is listening, and that is the entire question it answers. It is deliberately independent of configuration, so it stays 200 even when this instance would refuse to start - see /healthz below for the question that actually depends on being configured correctly. Point a container orchestrator's liveness probe or a load balancer's own target-health check at it; do not point a multi-region failover check at it - see Multi-region.

Reading /healthz​

It answers one question - can this instance sign somebody in? - and is deliberately terse, because it is unauthenticated. What to look for:

  • version - the deployed SAG release, so a fleet behind a load balancer can be checked for a stale instance after a rollout.
  • signing.primary.ephemeral: true - the instance generated its own key at start-up and will invalidate every token it has issued when it restarts. Only ever acceptable in development.
  • warnings - anything in here was tolerated at start-up rather than fatal, so it is worth reading after every deployment.
  • routes.upstreams - a count per provider, so {"microsoft": 3} means three upstream registrations. Which domains they serve is not published.
  • peer_jwks - only present with PEER_JWKS_URLS set. A peer with within_grace_period: false has had its keys dropped from /jwks.json entirely, which means it has been unreachable for a very long time by design - see Multi-region.

What it deliberately will not tell you​

Whether a state store is configured, and therefore whether authorisation codes are single-use and OTP sends are limited, is not published, and neither is anything that names an upstream domain or a relying party. A map of which defences are on and who is behind this deployment is more useful to somebody deciding what to try than it is to you.

Those warnings still exist. They are in the start-up banner on Node, and on every platform they are written to the log once per isolate as configuration warning with the text in detail:

node adapters/node/server.js               # banner, under "Warnings:"
wrangler tail | grep 'configuration warning'
aws logs tail /aws/lambda/sag --follow | grep 'configuration warning'

If you need a machine-readable answer to "is the state store there?", the honest test is behavioural: redeem an authorisation code twice and check the second attempt is refused. That is what test/local-stack/verify.js does.

Checking a deployment refuses to be insecure​

The design principle is that development defaults become hard errors as soon as a real hostname is in play. It is worth confirming that on a new deployment rather than trusting it:

SAG_ISSUER=https://id.example.com node adapters/node/server.js

With nothing else set, that must refuse to start and list the reasons - no master secret, no signing key, no subject salt, and a console email provider. If it starts, something is wrong with the configuration being passed in.